How to Install a New Toilet in 5 Easy Steps.

Published: 17th August 2005
Views: N/A


How to Install a New Toilet in 5 Easy Steps.

If your toilet is old and in need of repairs, it is cheaper to
replace it by installing a new one. This is quite easy to do and can
be completed in an afternoon. However, if you plan to install a
toilet in a new location, you will have to extend supply pipes and
drainpipes to the desired spot, a job you may want to leave to a
plumbing contractor.

Most toilets are sold with the necessary gaskets, washers, and
hardware for fitting the tank to the bowl. However you might need to
buy a few parts. Here is a list of what you need to complete this
task:

- Toilet bowl
- Toilet tank
- Toilet seat
- Two 1/4" bolts for bowl to flange
- Wax ring
- 20" water supply with fitting at valve or floor connection Tools:
Pair of channel pliers, bucket, screw driver.

(Many of these can be ordered online at any DIY website such as DIY
Tips UK: http://www.diy-tips-uk.com/plumbing/)

1. Shut off the water to the toilet, use a bucket and a cloth or a
sponge to remove the water left in tank and bowl after you flush the
toilet.

2. Using a pair of channel pliers, or a small pipe wrench (8"),
remove the nut where the water line fastens to the ballcock valve
under the left side of the bottom of the tank. Next use a small
crescent wrench, remove the two 1/4" nuts holding the bowl to the
floor flange. Remove old toilet. Remove the water line from the
valve or fitting at floor or wall.

3. Now you are ready to install your new toilet. Put the two 1/4"
bolts in the side holes of the flange with the bolt head in the
flange. Put some of the old wax at this spot to hold the bolts
straight up and across from each other. Put new wax ring on flange,
flat side up if tapered.

4. Set new bowl only straight down so it centers on wax ring and
both bolts come through holds on each side of bowl. Sit on bowl
facing wall until your weight puts bowl flush with the floor. Put
metal washers and nuts on bolts and tighten until snug. Do not over-
tighten as you can crack the bowl. Tighten these again after toilet
is completely installed and filled with water.

5. Next put 2" rubber gasket on tank where it sets on the bowl, put
rubber washers on bolts provided under the bolt head so they will be
on the inside of the tank. Pick up tank and set on bowl over holes
in bowl where bolts go through. Sit on bowl facing wall. Put bolts
on from the inside of the tank into holes in bowl, put on metal
washers and nuts and tighten. Hold tank level and tighten so it
brings tank down level. Use a large screw driver inside tank and a
crescent wrench or end wrench to back up nut under bowl. Tighten
with screw driver. Hook water supply to tank, turn on water, check
for leaks, and snug up the bolts holding bowl to floor. If there is
a space between the back of the tank and the wall, put a spacer of
sort there to brace tank. A piece of wood or hard rubber works fine.

Maintenance:

At least twice a year clean out the inside of your toilet tank. When
cleaning the toilet tank, turn off the water, flush toilet once, add
small amount of cleaning detergent inside tank to water remaining
and use a cloth or brush to clean. Also clean out holes under toilet
seat and rim of the bowl as well as the 3/4" hole in the bottom of
toilet bowl. Replace rubber tank ball at this time if needed.
Maintaining your new toilet will keep the plumber away and reduce
your plumbing bill.

Copyright © 2005. Bridget Mwape writes for DIY Tips UK:
http://www.diy-tips-uk.com/ which features how-to articles and
products to help you with your DIY and home improvement projects.
This article may be reprinted as long as all the above links are
active and clickable and this author box (byline) is not edited.


Video Source: Youtube


Report this article Ask About This Article


Loading...
More to Explore